When a metal component needs a coating, there are three common routes: plastisol dip coating, fluidized bed coating with thermoplastic powders, and electrostatic powder coating. All three put a plastic layer on the metal, but the results differ greatly in thickness, feel, protection and cost.
Choosing the wrong technology is one of the most common mistakes we see in our shop: a powder-coated handle that slips, a coating too thick to stay within tolerances, a complex part with uncovered areas. In this article we explain how each method works and how to tell which one is right for your part.
If you are starting from scratch, our guide to metal plastic coating explains the basics of the process.
The three technologies at a glance
Plastisol dip coating
The part is preheated and dipped into a tank of liquid plastisol, a suspension of PVC in a plasticizer. The heat of the metal makes the material adhere; in the oven the plastisol fuses and consolidates into a continuous, flexible, soft layer. The hotter the part and the longer it stays immersed, the thicker the coating: from less than a millimeter up to several millimeters.
This is the technology that gives handles, levers and grips their typical rubbery finish, and the one that best covers complex shapes, cavities and wire.
Fluidized bed (thermoplastic powders)
The hot part is dipped into a tank where a thermoplastic powder (for example polyethylene or polyamide) is kept in suspension by an air flow, so that it behaves almost like a liquid. The powder melts on contact with the metal and forms a hard, smooth layer, generally a few tenths of a millimeter thick.
It produces coatings that resist abrasion and chemicals, but without the soft feel of plastisol, and it tends to round off fine details.
Electrostatic powder coating
An electrically charged powder is sprayed onto the part and then cured in an oven. The layer is thin and hard; the choice of colors and decorative effects is very wide. It is the most common solution for decorative finishes on large runs, but it is not designed to cushion, insulate or improve grip.
Side-by-side comparison
| Dip coating (plastisol) | Fluidized bed | Powder coating | |
|---|---|---|---|
| Typical thickness | From less than 1 mm to several mm | A few tenths of a mm | Thin layer |
| Feel | Soft, rubbery | Hard, smooth | Hard, smooth or textured |
| Grip and non-slip | Excellent | Poor | Poor |
| Impact and noise damping | Excellent | Limited | None |
| Electrical insulation | Good (depends on thickness) | Good | Limited |
| Complex shapes and wire | Excellent: dipping reaches everywhere | Good | Difficult in cavities and shielded corners |
| Fine visible details | Tends to round them off | Tends to round them off | Preserves them |
| Decorative range | Solid colors, matte or glossy finishes | Limited | Very wide |
Indicative values: thickness and performance depend on material, part and process parameters.
How to choose: start from what the part has to do
The right question is not “which technology is best” but “what does the coating have to do”. A few rules of thumb:
- The part will be held in the hand (levers, handles, tools, footplates): plastisol dip coating. Grip and soft feel are its strengths.
- The part must absorb impact or vibration, or protect whatever it touches (hooks, supports, transport protection): dip coating.
- A component must be electrically insulated: dip coating. It achieves greater thickness, and therefore better insulation, and it can insulate just part of the item.
- Abrasion resistance with a hard layer is needed, for example on grids and baskets: fluidized bed.
- Appearance matters most, on flat surfaces with special colors and tight tolerances: powder coating.
They can be combined. The same part often needs more than one finish: for example a powder-coated sheet metal part with a plastic-coated grip area, or a component masked where it has to be welded or threaded. This is the kind of assessment we make at the start of every project. We handle powder coating through selected external suppliers, so you deal with a single contact.
How the technology affects cost
Each technology has a different setup cost: fixtures to hold the parts, color changes, the minimum amount of material in the tank. On small batches of complex shapes, dip coating is often the most cost-effective, because fixtures are simple and the coating covers the part in a single pass. On large runs of flat parts, powder coating has very low unit costs.
We have written a separate article on everything that determines the price of plastic coating.
The most common mistakes
- Choosing powder coating for a part that will be held. It is cheaper at first, but the end customer immediately notices that it slips or chips; it also does not take the sharp edge off and does not provide a comfortable grip.
- Not allowing for coating thickness in the dimensions. A dip coating a few millimeters thick changes the size of the part: holes, joints and fits must be designed with this in mind, or masked.
- Neglecting surface preparation. Oxides, oils and machining residues undermine adhesion with any technology.
- Designing sharp edges for powder coating or fluidized bed. These coatings get thinner on edges: a small radius improves durability. With dip coating this is not an issue, because plastisol rounds off edges by itself.
Frequently asked questions
Is plastisol dip coating the same as rubber coating?
In everyday language, yes: “rubber coating” is the term used when the dip coating has a soft, non-slip finish. We cover it in our article on rubber coating for metal.
Can a plastic-coated part be powder coated afterwards?
Generally, no: powder coating curing temperatures are not compatible with a plastisol coating that has already been applied. If both finishes are needed, the order of operations is planned in advance and the relevant areas are masked.
Which technology gives the best corrosion protection?
It depends more on the thickness and integrity of the layer than on the technology itself. Thick dip and fluidized bed coatings provide a more robust physical barrier; real-world durability should be assessed against the operating environment.
Not sure which to choose?
Send us the drawing or a photo of the part and tell us how it will be used: we will tell you which technology makes sense and why, even when the answer is not plastic coating.